/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
* irmpconfig.h\r
*\r
- * Copyright (c) 2010 Frank Meyer - frank(at)fli4l.de\r
+ * DO NOT INCLUDE THIS FILE, WILL BE INCLUDED BY IRMP.H!\r
*\r
- * $Id: irmpconfig.h,v 1.63 2011/03/10 12:29:14 fm Exp $\r
+ * Copyright (c) 2009-2013 Frank Meyer - frank(at)fli4l.de\r
+ *\r
+ * $Id: irmpconfig.h,v 1.101 2013/04/09 12:02:51 fm Exp $\r
*\r
* ATMEGA88 @ 8 MHz\r
*\r
#ifndef _IRMPCONFIG_H_\r
#define _IRMPCONFIG_H_\r
\r
+#ifndef _IRMP_H_\r
+# error please include only irmp.h, not irmpconfig.h\r
+#endif\r
+\r
/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
* Change F_INTERRUPTS if you change the number of interrupts per second,\r
* Normally, F_INTERRUPTS should be in the range from 10000 to 15000, typical is 15000\r
*---------------------------------------------------------------------------------------------------------------------------------------------------\r
*/\r
#ifndef F_INTERRUPTS\r
-#define F_INTERRUPTS 15000 // interrupts per second, min: 10000, max: 20000, typ: 15000\r
+# define F_INTERRUPTS 15000 // interrupts per second, min: 10000, max: 20000, typ: 15000\r
#endif\r
\r
/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
* 0 disable decoder\r
*\r
* The standard decoders are enabled per default.\r
- * Some less common protocols are disabled here, you need to enable them manually.\r
+ * Less common protocols are disabled here, you need to enable them manually.\r
*\r
* If you want to use FDC or RCCAR simultaneous with RC5 protocol, additional program space is required.\r
* If you don't need RC5 when using FDC/RCCAR, you should disable RC5.\r
+ * You cannot enable both DENON and RUWIDO, only enable one of them.\r
*---------------------------------------------------------------------------------------------------------------------------------------------------\r
*/\r
\r
-// Typical Protocols, disable here! Enable Remarks F_INTERRUPTS Program Space\r
+// typical protocols, disable here! Enable Remarks F_INTERRUPTS Program Space\r
#define IRMP_SUPPORT_SIRCS_PROTOCOL 1 // Sony SIRCS >= 10000 ~150 bytes\r
#define IRMP_SUPPORT_NEC_PROTOCOL 1 // NEC + APPLE >= 10000 ~300 bytes\r
#define IRMP_SUPPORT_SAMSUNG_PROTOCOL 1 // Samsung + Samsung32 >= 10000 ~300 bytes\r
#define IRMP_SUPPORT_MATSUSHITA_PROTOCOL 1 // Matsushita >= 10000 ~50 bytes\r
#define IRMP_SUPPORT_KASEIKYO_PROTOCOL 1 // Kaseikyo >= 10000 ~250 bytes\r
#define IRMP_SUPPORT_DENON_PROTOCOL 1 // DENON, Sharp >= 10000 ~250 bytes\r
-#define IRMP_SUPPORT_RC5_PROTOCOL 1 // RC5 >= 10000 ~250 bytes\r
\r
-// More Protocols, enable here! Enable Remarks F_INTERRUPTS Program Space\r
+// more protocols, enable here! Enable Remarks F_INTERRUPTS Program Space\r
+#define IRMP_SUPPORT_RC5_PROTOCOL 0 // RC5 >= 10000 ~250 bytes\r
+#define IRMP_SUPPORT_RC6_PROTOCOL 0 // RC6 & RC6A >= 10000 ~250 bytes\r
#define IRMP_SUPPORT_JVC_PROTOCOL 0 // JVC >= 10000 ~150 bytes\r
#define IRMP_SUPPORT_NEC16_PROTOCOL 0 // NEC16 >= 10000 ~100 bytes\r
-#define IRMP_SUPPORT_NEC42_PROTOCOL 0 // NEC42 >= 10000 ~100 bytes\r
-#define IRMP_SUPPORT_RC6_PROTOCOL 0 // RC6 & RC6A >= 10000 ~250 bytes\r
-#define IRMP_SUPPORT_IR60_PROTOCOL 0 // IR60 (SAB2008) >= 10000 ~300 bytes\r
+#define IRMP_SUPPORT_NEC42_PROTOCOL 0 // NEC42 >= 10000 ~300 bytes\r
+#define IRMP_SUPPORT_IR60_PROTOCOL 0 // IR60 (SDA2008) >= 10000 ~300 bytes\r
#define IRMP_SUPPORT_GRUNDIG_PROTOCOL 0 // Grundig >= 10000 ~300 bytes\r
+#define IRMP_SUPPORT_SIEMENS_PROTOCOL 0 // Siemens Gigaset >= 15000 ~550 bytes\r
#define IRMP_SUPPORT_NOKIA_PROTOCOL 0 // Nokia >= 10000 ~300 bytes\r
+\r
+// exotic protocols, enable here! Enable Remarks F_INTERRUPTS Program Space\r
+#define IRMP_SUPPORT_BOSE_PROTOCOL 0 // BOSE >= 10000 ~150 bytes\r
#define IRMP_SUPPORT_KATHREIN_PROTOCOL 0 // Kathrein >= 10000 ~200 bytes\r
#define IRMP_SUPPORT_NUBERT_PROTOCOL 0 // NUBERT >= 10000 ~50 bytes\r
#define IRMP_SUPPORT_BANG_OLUFSEN_PROTOCOL 0 // Bang & Olufsen >= 10000 ~200 bytes\r
-#define IRMP_SUPPORT_NIKON_PROTOCOL 0 // NIKON >= 10000 ~250 bytes\r
+#define IRMP_SUPPORT_RECS80_PROTOCOL 0 // RECS80 (SAA3004) >= 15000 ~50 bytes\r
+#define IRMP_SUPPORT_RECS80EXT_PROTOCOL 0 // RECS80EXT (SAA3008) >= 15000 ~50 bytes\r
+#define IRMP_SUPPORT_THOMSON_PROTOCOL 0 // Thomson >= 10000 ~250 bytes\r
+#define IRMP_SUPPORT_NIKON_PROTOCOL 0 // NIKON camera >= 10000 ~250 bytes\r
#define IRMP_SUPPORT_NETBOX_PROTOCOL 0 // Netbox keyboard >= 10000 ~400 bytes (PROTOTYPE!)\r
-#define IRMP_SUPPORT_IMON_PROTOCOL 0 // IMON keyboard >= 10000 ~400 bytes (PROTOTYPE!)\r
+#define IRMP_SUPPORT_ORTEK_PROTOCOL 0 // ORTEK (Hama) >= 10000 ~150 bytes\r
+#define IRMP_SUPPORT_TELEFUNKEN_PROTOCOL 0 // Telefunken 1560 >= 10000 ~150 bytes\r
#define IRMP_SUPPORT_FDC_PROTOCOL 0 // FDC3402 keyboard >= 10000 (better 15000) ~150 bytes (~400 in combination with RC5)\r
#define IRMP_SUPPORT_RCCAR_PROTOCOL 0 // RC Car >= 10000 (better 15000) ~150 bytes (~500 in combination with RC5)\r
-#define IRMP_SUPPORT_SIEMENS_PROTOCOL 0 // Siemens Gigaset >= 15000 ~550 bytes\r
+#define IRMP_SUPPORT_ROOMBA_PROTOCOL 0 // iRobot Roomba >= 10000 ~150 bytes\r
#define IRMP_SUPPORT_RUWIDO_PROTOCOL 0 // RUWIDO, T-Home >= 15000 ~550 bytes\r
-#define IRMP_SUPPORT_RECS80_PROTOCOL 0 // RECS80 (SAA3004) >= 15000 ~50 bytes\r
-#define IRMP_SUPPORT_RECS80EXT_PROTOCOL 0 // RECS80EXT (SAA3008) >= 15000 ~50 bytes\r
+#define IRMP_SUPPORT_A1TVBOX_PROTOCOL 0 // A1 TV BOX >= 15000 (better 20000) ~300 bytes\r
+#define IRMP_SUPPORT_LEGO_PROTOCOL 0 // LEGO Power RC >= 20000 ~150 bytes\r
+\r
\r
/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
- * Change hardware pin here:\r
+ * Change hardware pin here for ATMEL AVR\r
*---------------------------------------------------------------------------------------------------------------------------------------------------\r
*/\r
-#ifdef PIC_CCS_COMPILER // PIC CCS Compiler:\r
+#if defined (ATMEL_AVR) // use PB6 as IR input on AVR\r
+# define IRMP_PORT_LETTER B\r
+# define IRMP_BIT_NUMBER 6\r
\r
-#define IRMP_PIN PIN_B4 // use PB4 as IR input on PIC\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Change hardware pin here for PIC C18 compiler\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#elif defined (PIC_C18) // use RB4 as IR input on PIC\r
+# define IRMP_PIN PORTBbits.RB4\r
\r
-#else // AVR:\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Change hardware pin here for PIC CCS compiler\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#elif defined (PIC_CCS)\r
+# define IRMP_PIN PIN_B4 // use PB4 as IR input on PIC\r
\r
-#define IRMP_PORT PORTB\r
-#define IRMP_DDR DDRB\r
-#define IRMP_PIN PINB\r
-#define IRMP_BIT 6 // use PB6 as IR input on AVR\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Change hardware pin here for ARM STM32\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#elif defined (ARM_STM32) // use C13 as IR input on STM32\r
+# define IRMP_PORT_LETTER C\r
+# define IRMP_BIT_NUMBER 13\r
\r
-#define input(x) ((x) & (1 << IRMP_BIT))\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Change hardware pin here for Stellaris ARM Cortex M4\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#elif defined (STELLARIS_ARM_CORTEX_M4) // use B4 as IR input on Stellaris LM4F\r
+# define IRMP_PORT_LETTER B\r
+# define IRMP_BIT_NUMBER 4\r
+\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Handling of unknown target system: DON'T CHANGE\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#elif !defined (UNIX_OR_WINDOWS)\r
+# error target system not defined.\r
#endif\r
\r
/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
*---------------------------------------------------------------------------------------------------------------------------------------------------\r
*/\r
#ifndef IRMP_LOGGING\r
-#define IRMP_LOGGING 0 // 1: log IR signal (scan), 0: do not (default)\r
+# define IRMP_LOGGING 0 // 1: log IR signal (scan), 0: do not. default is 0\r
#endif\r
\r
/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
- * DO NOT CHANGE THE FOLLOWING LINES !\r
+ * Use external logging routines\r
+ * If you enable external logging, you have also to enable IRMP_LOGGING above\r
*---------------------------------------------------------------------------------------------------------------------------------------------------\r
*/\r
-#if IRMP_SUPPORT_SIEMENS_PROTOCOL == 1 && F_INTERRUPTS < 15000\r
-#warning F_INTERRUPTS too low, SIEMENS protocol disabled (should be at least 15000)\r
-#undef IRMP_SUPPORT_SIEMENS_PROTOCOL\r
-#define IRMP_SUPPORT_SIEMENS_PROTOCOL 0\r
-#endif\r
-\r
-#if IRMP_SUPPORT_RUWIDO_PROTOCOL == 1 && F_INTERRUPTS < 15000\r
-#warning F_INTERRUPTS too low, RUWIDO protocol disabled (should be at least 15000)\r
-#undef IRMP_SUPPORT_RUWIDO_PROTOCOL\r
-#define IRMP_SUPPORT_RUWIDO_PROTOCOL 0\r
-#endif\r
-\r
-#if IRMP_SUPPORT_RECS80_PROTOCOL == 1 && F_INTERRUPTS < 15000\r
-#warning F_INTERRUPTS too low, RECS80 protocol disabled (should be at least 15000)\r
-#undef IRMP_SUPPORT_RECS80_PROTOCOL\r
-#define IRMP_SUPPORT_RECS80_PROTOCOL 0\r
-#endif\r
-\r
-#if IRMP_SUPPORT_RECS80EXT_PROTOCOL == 1 && F_INTERRUPTS < 15000\r
-#warning F_INTERRUPTS too low, RECS80EXT protocol disabled (should be at least 15000)\r
-#undef IRMP_SUPPORT_RECS80EXT_PROTOCOL\r
-#define IRMP_SUPPORT_RECS80EXT_PROTOCOL 0\r
-#endif\r
-\r
-#if IRMP_SUPPORT_JVC_PROTOCOL == 1 && IRMP_SUPPORT_NEC_PROTOCOL == 0\r
-#warning JVC protocol needs also NEC protocol, NEC protocol enabled\r
-#undef IRMP_SUPPORT_NEC_PROTOCOL\r
-#define IRMP_SUPPORT_NEC_PROTOCOL 1\r
+#ifndef IRMP_EXT_LOGGING\r
+# define IRMP_EXT_LOGGING 0 // 1: use external logging, 0: do not. default is 0\r
#endif\r
\r
-#if IRMP_SUPPORT_NEC16_PROTOCOL == 1 && IRMP_SUPPORT_NEC_PROTOCOL == 0\r
-#warning NEC16 protocol needs also NEC protocol, NEC protocol enabled\r
-#undef IRMP_SUPPORT_NEC_PROTOCOL\r
-#define IRMP_SUPPORT_NEC_PROTOCOL 1\r
-#endif\r
-\r
-#if IRMP_SUPPORT_NEC42_PROTOCOL == 1 && IRMP_SUPPORT_NEC_PROTOCOL == 0\r
-#warning NEC42 protocol needs also NEC protocol, NEC protocol enabled\r
-#undef IRMP_SUPPORT_NEC_PROTOCOL\r
-#define IRMP_SUPPORT_NEC_PROTOCOL 1\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Set IRMP_PROTOCOL_NAMES to 1 if want to access protocol names (for logging etc), costs ~300 bytes RAM!\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#ifndef IRMP_PROTOCOL_NAMES\r
+# define IRMP_PROTOCOL_NAMES 0 // 1: access protocol names, 0: do not. default is 0\r
#endif\r
\r
-#if F_INTERRUPTS > 20000\r
-#error F_INTERRUPTS too high (should be not greater than 20000)\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Use Callbacks to indicate input signal\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#ifndef IRMP_USE_CALLBACK\r
+# define IRMP_USE_CALLBACK 0 // 1: use callbacks. 0: do not. default is 0\r
#endif\r
\r
#endif /* _WC_IRMPCONFIG_H_ */\r
projects / irmp.git / blobdiff