/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
* irmpconfig.h\r
*\r
- * Copyright (c) 2010 Frank Meyer - frank(at)fli4l.de\r
+ * DO NOT INCLUDE THIS FILE, WILL BE INCLUDED BY IRMP.H!\r
*\r
- * $Id: irmpconfig.h,v 1.22 2010/06/15 12:02:52 fm Exp $\r
+ * Copyright (c) 2009-2015 Frank Meyer - frank(at)fli4l.de\r
+ * Extensions for PIC 12F1820 W.Strobl 2014-07-20\r
*\r
- * ATMEGA88 @ 8 MHz\r
+ * $Id: irmpconfig.h,v 1.133 2015/06/15 10:30:10 fm Exp $\r
*\r
* This program is free software; you can redistribute it and/or modify\r
* it under the terms of the GNU General Public License as published by\r
#ifndef _IRMPCONFIG_H_\r
#define _IRMPCONFIG_H_\r
\r
+#ifndef _IRMP_H_\r
+# error please include only irmp.h, not irmpconfig.h\r
+#endif\r
+\r
/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
- * Change F_INTERRUPTS if you change the number of interrupts per second, F_INTERRUPTS should be in the range from 10000 to 15000\r
+ * Change F_INTERRUPTS if you change the number of interrupts per second,\r
+ * Normally, F_INTERRUPTS should be in the range from 10000 to 15000, typical is 15000\r
+ * A value above 15000 costs additional program space, absolute maximum value is 20000.\r
+ * On PIC with XC8/C18 Compiler, use 15151 as the correct value.\r
*---------------------------------------------------------------------------------------------------------------------------------------------------\r
*/\r
#ifndef F_INTERRUPTS\r
-#define F_INTERRUPTS 10000 // interrupts per second, min: 10000, max: 15000\r
+# define F_INTERRUPTS 15000 // interrupts per second, min: 10000, max: 20000, typ: 15000\r
#endif\r
\r
/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
* Change settings from 1 to 0 if you want to disable one or more decoders.\r
* This saves program space.\r
+ *\r
* 1 enable decoder\r
* 0 disable decoder\r
+ *\r
+ * The standard decoders are enabled per default.\r
+ * Less common protocols are disabled here, you need to enable them manually.\r
+ *\r
+ * If you want to use FDC or RCCAR simultaneous with RC5 protocol, additional program space is required.\r
+ * If you don't need RC5 when using FDC/RCCAR, you should disable RC5.\r
+ * You cannot enable both DENON and RUWIDO, only enable one of them.\r
*---------------------------------------------------------------------------------------------------------------------------------------------------\r
*/\r
-#define IRMP_SUPPORT_SIRCS_PROTOCOL 1 // flag: support SIRCS uses ~100 bytes\r
-#define IRMP_SUPPORT_NEC_PROTOCOL 1 // flag: support NEC + APPLE uses ~250 bytes\r
-#define IRMP_SUPPORT_SAMSUNG_PROTOCOL 1 // flag: support Samsung + Samsung32 uses ~250 bytes\r
-#define IRMP_SUPPORT_MATSUSHITA_PROTOCOL 1 // flag: support Matsushita uses ~50 bytes\r
-#define IRMP_SUPPORT_KASEIKYO_PROTOCOL 1 // flag: support Kaseikyo uses ~50 bytes\r
-#define IRMP_SUPPORT_RECS80_PROTOCOL 1 // flag: support RECS80 uses ~50 bytes\r
-#define IRMP_SUPPORT_RC5_PROTOCOL 1 // flag: support RC5 uses ~250 bytes\r
-#define IRMP_SUPPORT_DENON_PROTOCOL 1 // flag: support DENON uses ~250 bytes\r
-#define IRMP_SUPPORT_RC6_PROTOCOL 1 // flag: support RC6 uses ~200 bytes\r
-#define IRMP_SUPPORT_RECS80EXT_PROTOCOL 1 // flag: support RECS80EXT uses ~50 bytes\r
-#define IRMP_SUPPORT_NUBERT_PROTOCOL 1 // flag: support NUBERT uses ~50 bytes\r
-#define IRMP_SUPPORT_BANG_OLUFSEN_PROTOCOL 1 // flag: support Bang & Olufsen uses ~200 bytes\r
-#define IRMP_SUPPORT_GRUNDIG_PROTOCOL 1 // flag: support Grundig uses ~150 bytes\r
-#define IRMP_SUPPORT_NOKIA_PROTOCOL 1 // flag: support Nokia uses ~150 bytes\r
-#define IRMP_SUPPORT_FDC_PROTOCOL 0 // flag: support FDC3402 keyboard uses ~50 bytes\r
-#define IRMP_SUPPORT_RCCAR_PROTOCOL 0 // flag: support RC car uses ~150 bytes\r
+\r
+// typical protocols, disable here! Enable Remarks F_INTERRUPTS Program Space\r
+#define IRMP_SUPPORT_SIRCS_PROTOCOL 1 // Sony SIRCS >= 10000 ~150 bytes\r
+#define IRMP_SUPPORT_NEC_PROTOCOL 1 // NEC + APPLE >= 10000 ~300 bytes\r
+#define IRMP_SUPPORT_SAMSUNG_PROTOCOL 1 // Samsung + Samsg32 >= 10000 ~300 bytes\r
+#define IRMP_SUPPORT_KASEIKYO_PROTOCOL 1 // Kaseikyo >= 10000 ~250 bytes\r
+\r
+// more protocols, enable here! Enable Remarks F_INTERRUPTS Program Space\r
+#define IRMP_SUPPORT_JVC_PROTOCOL 0 // JVC >= 10000 ~150 bytes\r
+#define IRMP_SUPPORT_NEC16_PROTOCOL 0 // NEC16 >= 10000 ~100 bytes\r
+#define IRMP_SUPPORT_NEC42_PROTOCOL 0 // NEC42 >= 10000 ~300 bytes\r
+#define IRMP_SUPPORT_MATSUSHITA_PROTOCOL 0 // Matsushita >= 10000 ~50 bytes\r
+#define IRMP_SUPPORT_DENON_PROTOCOL 0 // DENON, Sharp >= 10000 ~250 bytes\r
+#define IRMP_SUPPORT_RC5_PROTOCOL 0 // RC5 >= 10000 ~250 bytes\r
+#define IRMP_SUPPORT_RC6_PROTOCOL 0 // RC6 & RC6A >= 10000 ~250 bytes\r
+#define IRMP_SUPPORT_IR60_PROTOCOL 0 // IR60 (SDA2008) >= 10000 ~300 bytes\r
+#define IRMP_SUPPORT_GRUNDIG_PROTOCOL 0 // Grundig >= 10000 ~300 bytes\r
+#define IRMP_SUPPORT_SIEMENS_PROTOCOL 0 // Siemens Gigaset >= 15000 ~550 bytes\r
+#define IRMP_SUPPORT_NOKIA_PROTOCOL 0 // Nokia >= 10000 ~300 bytes\r
+\r
+// exotic protocols, enable here! Enable Remarks F_INTERRUPTS Program Space\r
+#define IRMP_SUPPORT_BOSE_PROTOCOL 0 // BOSE >= 10000 ~150 bytes\r
+#define IRMP_SUPPORT_KATHREIN_PROTOCOL 0 // Kathrein >= 10000 ~200 bytes\r
+#define IRMP_SUPPORT_NUBERT_PROTOCOL 0 // NUBERT >= 10000 ~50 bytes\r
+#define IRMP_SUPPORT_FAN_PROTOCOL 0 // FAN (ventilator) >= 10000 ~50 bytes\r
+#define IRMP_SUPPORT_SPEAKER_PROTOCOL 0 // SPEAKER (~NUBERT) >= 10000 ~50 bytes\r
+#define IRMP_SUPPORT_BANG_OLUFSEN_PROTOCOL 0 // Bang & Olufsen >= 10000 ~200 bytes\r
+#define IRMP_SUPPORT_RECS80_PROTOCOL 0 // RECS80 (SAA3004) >= 15000 ~50 bytes\r
+#define IRMP_SUPPORT_RECS80EXT_PROTOCOL 0 // RECS80EXT (SAA3008) >= 15000 ~50 bytes\r
+#define IRMP_SUPPORT_THOMSON_PROTOCOL 0 // Thomson >= 10000 ~250 bytes\r
+#define IRMP_SUPPORT_NIKON_PROTOCOL 0 // NIKON camera >= 10000 ~250 bytes\r
+#define IRMP_SUPPORT_NETBOX_PROTOCOL 0 // Netbox keyboard >= 10000 ~400 bytes (PROTOTYPE!)\r
+#define IRMP_SUPPORT_ORTEK_PROTOCOL 0 // ORTEK (Hama) >= 10000 ~150 bytes\r
+#define IRMP_SUPPORT_TELEFUNKEN_PROTOCOL 0 // Telefunken 1560 >= 10000 ~150 bytes\r
+#define IRMP_SUPPORT_FDC_PROTOCOL 0 // FDC3402 keyboard >= 10000 (better 15000) ~150 bytes (~400 in combination with RC5)\r
+#define IRMP_SUPPORT_RCCAR_PROTOCOL 0 // RC Car >= 10000 (better 15000) ~150 bytes (~500 in combination with RC5)\r
+#define IRMP_SUPPORT_ROOMBA_PROTOCOL 0 // iRobot Roomba >= 10000 ~150 bytes\r
+#define IRMP_SUPPORT_RUWIDO_PROTOCOL 0 // RUWIDO, T-Home >= 15000 ~550 bytes\r
+#define IRMP_SUPPORT_A1TVBOX_PROTOCOL 0 // A1 TV BOX >= 15000 (better 20000) ~300 bytes\r
+#define IRMP_SUPPORT_LEGO_PROTOCOL 0 // LEGO Power RC >= 20000 ~150 bytes\r
+#define IRMP_SUPPORT_RCMM_PROTOCOL 0 // RCMM 12,24, or 32 >= 20000 ~150 bytes\r
+#define IRMP_SUPPORT_LGAIR_PROTOCOL 0 // LG Air Condition >= 10000 ~300 bytes\r
+#define IRMP_SUPPORT_SAMSUNG48_PROTOCOL 0 // Samsung48 >= 10000 ~100 bytes (SAMSUNG must be enabled!)\r
+#define IRMP_SUPPORT_MERLIN_PROTOCOL 0 // Merlin >= 15000 (better 20000) ~300 bytes\r
+#define IRMP_SUPPORT_PENTAX_PROTOCOL 0 // Pentax >= 10000 ~150 bytes\r
+#define IRMP_SUPPORT_S100_PROTOCOL 0 // S100 >= 10000 ~250 bytes\r
+#define IRMP_SUPPORT_ACP24_PROTOCOL 1 // ACP24 >= 10000 ~250 bytes\r
+#define IRMP_SUPPORT_RADIO1_PROTOCOL 0 // RADIO, e.g. TEVION >= 10000 ~250 bytes (experimental)\r
\r
/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
- * THE FOLLOWING DECODERS WORK ONLY FOR F_INTERRUPTS > 14500!\r
+ * Change hardware pin here for ATMEL ATMega/ATTiny/XMega\r
*---------------------------------------------------------------------------------------------------------------------------------------------------\r
*/\r
-#if F_INTERRUPTS >= 14500\r
-#define IRMP_SUPPORT_SIEMENS_PROTOCOL 1 // flag: support Siemens Gigaset uses ~150 bytes\r
-#else\r
-#define IRMP_SUPPORT_SIEMENS_PROTOCOL 0 // DO NOT CHANGE! F_INTERRUPTS too low!\r
-#endif\r
-\r
-#if IRMP_SUPPORT_FDC_PROTOCOL == 1 && IRMP_SUPPORT_RC5_PROTOCOL == 1\r
-#error Protocols RC5 and FDC may not be enabled both at the same time. Please disable one of them in irmpconfig.h.\r
-#endif\r
-\r
-#if IRMP_SUPPORT_RCCAR_PROTOCOL == 1 && IRMP_SUPPORT_RC5_PROTOCOL == 1\r
-#error Protocols RC5 and RCCAR may not be enabled both at the same time. Please disable one of them in irmpconfig.h.\r
-#endif\r
+#if defined (ATMEL_AVR) || defined (__AVR_XMEGA__) // use PB6 as IR input on AVR\r
+# define IRMP_PORT_LETTER B\r
+# define IRMP_BIT_NUMBER 6\r
\r
/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
- * Change hardware pin here:\r
+ * Change hardware pin here for PIC C18 or XC8 compiler\r
*---------------------------------------------------------------------------------------------------------------------------------------------------\r
*/\r
-#ifdef PIC_CCS_COMPILER // PIC CCS Compiler:\r
+#elif defined (PIC_C18) // use RB4 as IR input on PIC (C18 or XC8 compiler)\r
+# if defined(__12F1840)\r
+# define IRMP_PIN RA5 // on 12F1840 with XC8 compiler\r
+# else\r
+# define IRMP_PIN PORTBbits.RB4 // PIC C18\r
+# endif\r
\r
-#define IRMP_PIN PIN_B4 // use PB4 as IR input on PIC\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Change hardware pin here for PIC CCS compiler\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#elif defined (PIC_CCS)\r
+# define IRMP_PIN PIN_B4 // use PB4 as IR input on PIC (CCS compiler)\r
\r
-#else // AVR:\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Change hardware pin here for ARM STM32\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#elif defined (ARM_STM32) // use C13 as IR input on STM32\r
+# define IRMP_PORT_LETTER C\r
+# define IRMP_BIT_NUMBER 13\r
\r
-#define IRMP_PORT PORTB\r
-#define IRMP_DDR DDRB\r
-#define IRMP_PIN PINB\r
-#define IRMP_BIT 6 // use PB6 as IR input on AVR\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Change hardware pin here for Stellaris ARM Cortex M4\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#elif defined (STELLARIS_ARM_CORTEX_M4) // use B4 as IR input on Stellaris LM4F\r
+# define IRMP_PORT_LETTER B\r
+# define IRMP_BIT_NUMBER 4\r
\r
-#define input(x) ((x) & (1 << IRMP_BIT))\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Handling of unknown target system: DON'T CHANGE\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#elif !defined (UNIX_OR_WINDOWS)\r
+# error target system not defined.\r
#endif\r
\r
/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
*---------------------------------------------------------------------------------------------------------------------------------------------------\r
*/\r
#ifndef IRMP_LOGGING\r
-#define IRMP_LOGGING 0 // 1: log IR signal (scan), 0: do not (default)\r
+# define IRMP_LOGGING 0 // 1: log IR signal (scan), 0: do not. default is 0\r
+#endif\r
+\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Use external logging routines\r
+ * If you enable external logging, you have also to enable IRMP_LOGGING above\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#ifndef IRMP_EXT_LOGGING\r
+# define IRMP_EXT_LOGGING 0 // 1: use external logging, 0: do not. default is 0\r
+#endif\r
+\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Set IRMP_PROTOCOL_NAMES to 1 if want to access protocol names (for logging etc), costs ~300 bytes RAM!\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#ifndef IRMP_PROTOCOL_NAMES\r
+# define IRMP_PROTOCOL_NAMES 0 // 1: access protocol names, 0: do not. default is 0\r
+#endif\r
+\r
+/*---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ * Use Callbacks to indicate input signal\r
+ *---------------------------------------------------------------------------------------------------------------------------------------------------\r
+ */\r
+#ifndef IRMP_USE_CALLBACK\r
+# define IRMP_USE_CALLBACK 0 // 1: use callbacks. 0: do not. default is 0\r
#endif\r
\r
-#endif /* _WC_IRMPCONFIG_H_ */\r
+#endif // _IRMPCONFIG_H_\r