X-Git-Url: http://cloudbase.mooo.com/gitweb/irmp.git/blobdiff_plain/3521380001b19527424f9da3312b365948dfbc42..2ac088b274ff067eae9e5e391c9b3fddb5929624:/irmpconfig.h diff --git a/irmpconfig.h b/irmpconfig.h index 4507669..48ab0ec 100644 --- a/irmpconfig.h +++ b/irmpconfig.h @@ -1,9 +1,11 @@ /*--------------------------------------------------------------------------------------------------------------------------------------------------- * irmpconfig.h * - * Copyright (c) 2010 Frank Meyer - frank(at)fli4l.de + * DO NOT INCLUDE THIS FILE, WILL BE INCLUDED BY IRMP.H! * - * $Id: irmpconfig.h,v 1.63 2011/03/10 12:29:14 fm Exp $ + * Copyright (c) 2009-2013 Frank Meyer - frank(at)fli4l.de + * + * $Id: irmpconfig.h,v 1.98 2013/01/17 07:33:13 fm Exp $ * * ATMEGA88 @ 8 MHz * @@ -17,6 +19,10 @@ #ifndef _IRMPCONFIG_H_ #define _IRMPCONFIG_H_ +#ifndef _IRMP_H_ +# error please include only irmp.h, not irmpconfig.h +#endif + /*--------------------------------------------------------------------------------------------------------------------------------------------------- * Change F_INTERRUPTS if you change the number of interrupts per second, * Normally, F_INTERRUPTS should be in the range from 10000 to 15000, typical is 15000 @@ -24,7 +30,7 @@ *--------------------------------------------------------------------------------------------------------------------------------------------------- */ #ifndef F_INTERRUPTS -#define F_INTERRUPTS 15000 // interrupts per second, min: 10000, max: 20000, typ: 15000 +# define F_INTERRUPTS 15000 // interrupts per second, min: 10000, max: 20000, typ: 15000 #endif /*--------------------------------------------------------------------------------------------------------------------------------------------------- @@ -35,59 +41,94 @@ * 0 disable decoder * * The standard decoders are enabled per default. - * Some less common protocols are disabled here, you need to enable them manually. + * Less common protocols are disabled here, you need to enable them manually. * * If you want to use FDC or RCCAR simultaneous with RC5 protocol, additional program space is required. * If you don't need RC5 when using FDC/RCCAR, you should disable RC5. + * You cannot enable both DENON and RUWIDO, only enable one of them. *--------------------------------------------------------------------------------------------------------------------------------------------------- */ -// Typical Protocols, disable here! Enable Remarks F_INTERRUPTS Program Space +// typical protocols, disable here! Enable Remarks F_INTERRUPTS Program Space #define IRMP_SUPPORT_SIRCS_PROTOCOL 1 // Sony SIRCS >= 10000 ~150 bytes #define IRMP_SUPPORT_NEC_PROTOCOL 1 // NEC + APPLE >= 10000 ~300 bytes #define IRMP_SUPPORT_SAMSUNG_PROTOCOL 1 // Samsung + Samsung32 >= 10000 ~300 bytes #define IRMP_SUPPORT_MATSUSHITA_PROTOCOL 1 // Matsushita >= 10000 ~50 bytes #define IRMP_SUPPORT_KASEIKYO_PROTOCOL 1 // Kaseikyo >= 10000 ~250 bytes #define IRMP_SUPPORT_DENON_PROTOCOL 1 // DENON, Sharp >= 10000 ~250 bytes -#define IRMP_SUPPORT_RC5_PROTOCOL 1 // RC5 >= 10000 ~250 bytes -// More Protocols, enable here! Enable Remarks F_INTERRUPTS Program Space +// more protocols, enable here! Enable Remarks F_INTERRUPTS Program Space +#define IRMP_SUPPORT_RC5_PROTOCOL 0 // RC5 >= 10000 ~250 bytes +#define IRMP_SUPPORT_RC6_PROTOCOL 0 // RC6 & RC6A >= 10000 ~250 bytes #define IRMP_SUPPORT_JVC_PROTOCOL 0 // JVC >= 10000 ~150 bytes #define IRMP_SUPPORT_NEC16_PROTOCOL 0 // NEC16 >= 10000 ~100 bytes -#define IRMP_SUPPORT_NEC42_PROTOCOL 0 // NEC42 >= 10000 ~100 bytes -#define IRMP_SUPPORT_RC6_PROTOCOL 0 // RC6 & RC6A >= 10000 ~250 bytes -#define IRMP_SUPPORT_IR60_PROTOCOL 0 // IR60 (SAB2008) >= 10000 ~300 bytes +#define IRMP_SUPPORT_NEC42_PROTOCOL 0 // NEC42 >= 10000 ~300 bytes +#define IRMP_SUPPORT_IR60_PROTOCOL 0 // IR60 (SDA2008) >= 10000 ~300 bytes #define IRMP_SUPPORT_GRUNDIG_PROTOCOL 0 // Grundig >= 10000 ~300 bytes +#define IRMP_SUPPORT_SIEMENS_PROTOCOL 0 // Siemens Gigaset >= 15000 ~550 bytes #define IRMP_SUPPORT_NOKIA_PROTOCOL 0 // Nokia >= 10000 ~300 bytes + +// exotic protocols, enable here! Enable Remarks F_INTERRUPTS Program Space +#define IRMP_SUPPORT_BOSE_PROTOCOL 0 // BOSE >= 10000 ~150 bytes #define IRMP_SUPPORT_KATHREIN_PROTOCOL 0 // Kathrein >= 10000 ~200 bytes #define IRMP_SUPPORT_NUBERT_PROTOCOL 0 // NUBERT >= 10000 ~50 bytes #define IRMP_SUPPORT_BANG_OLUFSEN_PROTOCOL 0 // Bang & Olufsen >= 10000 ~200 bytes -#define IRMP_SUPPORT_NIKON_PROTOCOL 0 // NIKON >= 10000 ~250 bytes +#define IRMP_SUPPORT_RECS80_PROTOCOL 0 // RECS80 (SAA3004) >= 15000 ~50 bytes +#define IRMP_SUPPORT_RECS80EXT_PROTOCOL 0 // RECS80EXT (SAA3008) >= 15000 ~50 bytes +#define IRMP_SUPPORT_THOMSON_PROTOCOL 0 // Thomson >= 10000 ~250 bytes +#define IRMP_SUPPORT_NIKON_PROTOCOL 0 // NIKON camera >= 10000 ~250 bytes #define IRMP_SUPPORT_NETBOX_PROTOCOL 0 // Netbox keyboard >= 10000 ~400 bytes (PROTOTYPE!) -#define IRMP_SUPPORT_IMON_PROTOCOL 0 // IMON keyboard >= 10000 ~400 bytes (PROTOTYPE!) #define IRMP_SUPPORT_FDC_PROTOCOL 0 // FDC3402 keyboard >= 10000 (better 15000) ~150 bytes (~400 in combination with RC5) #define IRMP_SUPPORT_RCCAR_PROTOCOL 0 // RC Car >= 10000 (better 15000) ~150 bytes (~500 in combination with RC5) -#define IRMP_SUPPORT_SIEMENS_PROTOCOL 0 // Siemens Gigaset >= 15000 ~550 bytes #define IRMP_SUPPORT_RUWIDO_PROTOCOL 0 // RUWIDO, T-Home >= 15000 ~550 bytes -#define IRMP_SUPPORT_RECS80_PROTOCOL 0 // RECS80 (SAA3004) >= 15000 ~50 bytes -#define IRMP_SUPPORT_RECS80EXT_PROTOCOL 0 // RECS80EXT (SAA3008) >= 15000 ~50 bytes +#define IRMP_SUPPORT_A1TVBOX_PROTOCOL 0 // A1 TV BOX >= 15000 (better 20000) ~300 bytes +#define IRMP_SUPPORT_LEGO_PROTOCOL 0 // LEGO Power RC >= 20000 ~150 bytes + /*--------------------------------------------------------------------------------------------------------------------------------------------------- - * Change hardware pin here: + * Change hardware pin here for ATMEL AVR *--------------------------------------------------------------------------------------------------------------------------------------------------- */ -#ifdef PIC_CCS_COMPILER // PIC CCS Compiler: +#if defined (ATMEL_AVR) // use PB6 as IR input on AVR +# define IRMP_PORT_LETTER B +# define IRMP_BIT_NUMBER 6 -#define IRMP_PIN PIN_B4 // use PB4 as IR input on PIC +/*--------------------------------------------------------------------------------------------------------------------------------------------------- + * Change hardware pin here for PIC C18 compiler + *--------------------------------------------------------------------------------------------------------------------------------------------------- + */ +#elif defined (PIC_C18) // use RB4 as IR input on PIC +# define IRMP_PIN PORTBbits.RB4 -#else // AVR: +/*--------------------------------------------------------------------------------------------------------------------------------------------------- + * Change hardware pin here for PIC CCS compiler + *--------------------------------------------------------------------------------------------------------------------------------------------------- + */ +#elif defined (PIC_CCS) +# define IRMP_PIN PIN_B4 // use PB4 as IR input on PIC -#define IRMP_PORT PORTB -#define IRMP_DDR DDRB -#define IRMP_PIN PINB -#define IRMP_BIT 6 // use PB6 as IR input on AVR +/*--------------------------------------------------------------------------------------------------------------------------------------------------- + * Change hardware pin here for ARM STM32 + *--------------------------------------------------------------------------------------------------------------------------------------------------- + */ +#elif defined (ARM_STM32) // use C13 as IR input on STM32 +# define IRMP_PORT_LETTER C +# define IRMP_BIT_NUMBER 13 -#define input(x) ((x) & (1 << IRMP_BIT)) +/*--------------------------------------------------------------------------------------------------------------------------------------------------- + * Change hardware pin here for Stellaris ARM Cortex M4 + *--------------------------------------------------------------------------------------------------------------------------------------------------- + */ +#elif defined (STELLARIS_ARM_CORTEX_M4) // use B4 as IR input on Stellaris LM4F +# define IRMP_PORT_LETTER B +# define IRMP_BIT_NUMBER 4 + +/*--------------------------------------------------------------------------------------------------------------------------------------------------- + * Handling of unknown target system: DON'T CHANGE + *--------------------------------------------------------------------------------------------------------------------------------------------------- + */ +#elif !defined (UNIX_OR_WINDOWS) +# error target system not defined. #endif /*--------------------------------------------------------------------------------------------------------------------------------------------------- @@ -95,57 +136,32 @@ *--------------------------------------------------------------------------------------------------------------------------------------------------- */ #ifndef IRMP_LOGGING -#define IRMP_LOGGING 0 // 1: log IR signal (scan), 0: do not (default) +# define IRMP_LOGGING 0 // 1: log IR signal (scan), 0: do not. default is 0 #endif /*--------------------------------------------------------------------------------------------------------------------------------------------------- - * DO NOT CHANGE THE FOLLOWING LINES ! + * Use external logging routines + * If you enable external logging, you have also to enable IRMP_LOGGING above *--------------------------------------------------------------------------------------------------------------------------------------------------- */ -#if IRMP_SUPPORT_SIEMENS_PROTOCOL == 1 && F_INTERRUPTS < 15000 -#warning F_INTERRUPTS too low, SIEMENS protocol disabled (should be at least 15000) -#undef IRMP_SUPPORT_SIEMENS_PROTOCOL -#define IRMP_SUPPORT_SIEMENS_PROTOCOL 0 -#endif - -#if IRMP_SUPPORT_RUWIDO_PROTOCOL == 1 && F_INTERRUPTS < 15000 -#warning F_INTERRUPTS too low, RUWIDO protocol disabled (should be at least 15000) -#undef IRMP_SUPPORT_RUWIDO_PROTOCOL -#define IRMP_SUPPORT_RUWIDO_PROTOCOL 0 -#endif - -#if IRMP_SUPPORT_RECS80_PROTOCOL == 1 && F_INTERRUPTS < 15000 -#warning F_INTERRUPTS too low, RECS80 protocol disabled (should be at least 15000) -#undef IRMP_SUPPORT_RECS80_PROTOCOL -#define IRMP_SUPPORT_RECS80_PROTOCOL 0 -#endif - -#if IRMP_SUPPORT_RECS80EXT_PROTOCOL == 1 && F_INTERRUPTS < 15000 -#warning F_INTERRUPTS too low, RECS80EXT protocol disabled (should be at least 15000) -#undef IRMP_SUPPORT_RECS80EXT_PROTOCOL -#define IRMP_SUPPORT_RECS80EXT_PROTOCOL 0 -#endif - -#if IRMP_SUPPORT_JVC_PROTOCOL == 1 && IRMP_SUPPORT_NEC_PROTOCOL == 0 -#warning JVC protocol needs also NEC protocol, NEC protocol enabled -#undef IRMP_SUPPORT_NEC_PROTOCOL -#define IRMP_SUPPORT_NEC_PROTOCOL 1 +#ifndef IRMP_EXT_LOGGING +# define IRMP_EXT_LOGGING 0 // 1: use external logging, 0: do not. default is 0 #endif -#if IRMP_SUPPORT_NEC16_PROTOCOL == 1 && IRMP_SUPPORT_NEC_PROTOCOL == 0 -#warning NEC16 protocol needs also NEC protocol, NEC protocol enabled -#undef IRMP_SUPPORT_NEC_PROTOCOL -#define IRMP_SUPPORT_NEC_PROTOCOL 1 -#endif - -#if IRMP_SUPPORT_NEC42_PROTOCOL == 1 && IRMP_SUPPORT_NEC_PROTOCOL == 0 -#warning NEC42 protocol needs also NEC protocol, NEC protocol enabled -#undef IRMP_SUPPORT_NEC_PROTOCOL -#define IRMP_SUPPORT_NEC_PROTOCOL 1 +/*--------------------------------------------------------------------------------------------------------------------------------------------------- + * Set IRMP_PROTOCOL_NAMES to 1 if want to access protocol names (for logging etc), costs ~300 bytes RAM! + *--------------------------------------------------------------------------------------------------------------------------------------------------- + */ +#ifndef IRMP_PROTOCOL_NAMES +# define IRMP_PROTOCOL_NAMES 0 // 1: access protocol names, 0: do not. default is 0 #endif -#if F_INTERRUPTS > 20000 -#error F_INTERRUPTS too high (should be not greater than 20000) +/*--------------------------------------------------------------------------------------------------------------------------------------------------- + * Use Callbacks to indicate input signal + *--------------------------------------------------------------------------------------------------------------------------------------------------- + */ +#ifndef IRMP_USE_CALLBACK +# define IRMP_USE_CALLBACK 0 // 1: use callbacks. 0: do not. default is 0 #endif #endif /* _WC_IRMPCONFIG_H_ */